Frequently Asked Questions

Why is the letter I used to represent current?

The letter I seems to be an odd choice for the English language, but it was chosen in the early days of electricity to represent intensity of current which we simply call current today. The unit of current, the ampere, is named after the French scientist André-Marie Ampère in recognition of his work on the relationship between electric current and magnetism. Ampère referred to electric current as "l'intensité du courant électrique", so I was a logical choice to represent intensité (intensity). I am grateful to Barry Caruth for suggesting a search of the internet for "Ampère" and "l'intensité du courant électrique" which returns many sites as evidence (most of them French) enabling me to answer this question with confidence.
Further information: Quantities used in Electronics | Voltage and Current | Ohm's Law

Why do some books use zig-zag lines for resistors in circuit diagrams?

The zig-zag line is the old symbol for a resistor and you may find it in older books and magazines. Unfortunately a few publications still use it! The correct modern symbol for a resistor is a rectangle.
Further information: Resistors | Circuit Symbols | Circuit Diagrams

My project has a resistor labelled 47, does that mean 47k?

No, it means 47

which is 1000 times smaller! 47k

would be shortened to 47k (or 47K). The ohm (

) symbol is often omitted from circuit diagrams and component layouts but the k (meaning kilo = 1000) will always be included if it is needed.
Further information: Resistors

Why do resistors have odd values like 47k and 56k, but not 50k?

There is a good reason for these odd values and it is explained on the Resistors page.

Soldering iron stand, photograph © Rapid Electronics

Soldering iron stand
Photograph © Jupitor Electronics.

My soldering iron was supplied with a hook, do I really need to buy a stand as well?

For safety you must buy (or make) a stand for your soldering iron. Please don't use the hook because it leaves exposed the very hot element and tip of the iron - it is too easy to accidentally touch them and burn yourself. If you can't afford to buy a stand you could try making your own with a spiral of stiff galvanised iron wire (a coat-hanger?) screwed to a block of wood. Ideally the stand should include a damp sponge for safely wiping the tip of the iron when it needs cleaning.
Further information: Tools for Electronics | Soldering Guide

Where can I buy heatproof cable to replace the ordinary cable on my soldering iron?

Silicone heat resistant cable is sold in 1.5 metre lengths for exactly this purpose by Jupitor Electronics, part number 85-0590 (look in the Soldering Equipment section). If you use another supplier make sure you buy 3-core mains flex with a current rating of 3A (the proper name for mains appliance leads is flex, not cable). Please note that to change over to the new flex you will need to borrow a second soldering iron! This is because the flex is soldered to the iron's element. Make sure that you connect the wires correctly in the iron and in the mains plug which should have a 3A fuse.
Further information: Tools for Electronics | Soldering Guide

My teacher says that Christmas tree lights are a series circuit, so when one lamp blew on Christmas Eve why didn't they all go out?

Traditional Christmas tree lights are connected in series and you are correct in thinking that if one lamp blows all the lamps should go out. The problem is that Christmas tree lights are not like ordinary lamps! When they blow they automatically short-circuit (they become like a wire link) so the circuit is still complete and the other lamps remain lit. This makes it easy to see the blown lamp, but do remember to switch off before changing it.
Teachers - please be careful when giving Christmas tree lights as an example of a series circuit!
Further information: Series and Parallel Connections

What component has a black stripe in the centre (it looks like a diode)?

A small component about the size of a resistor or signal diode with a single black stripe in the centre is a zero-ohm resistor, it is really just a wire link! These components are used on commercial PCBs because they are easier for machines to handle than small pieces of wire. The single black stripe is logical because it means zero in the resistor colour code. Ordinary resistors have at least four stripes. Diodes have a single stripe near one end, not in the centre.
Further information: Diodes | Resistors

What is a "short circuit"?

A "short circuit" is a connection of very low resistance such as a wire (almost 0

) which provides a very easy path for current. Think of it as an electrical short-cut. It is normally used to describe a fault or accidental connection rather than a deliberate one.
For example: if the leads from a battery touch one another they create a very low resistance connection across the battery, so we say they have caused a short circuit across the battery. Current will flow through this short circuit rather than through the proper circuit. This stops the circuit working and it may cause a fire because the leads and battery will become hot with a large current flowing.
Further information: Voltage and Current | Resistance

What does "open circuit" mean?

"Open circuit" means no connection. It is usually used to describe a break in some part of a circuit which could be deliberate (such as a switch in the open or off position) or a fault (such as a broken wire or burnt out component).
Further information: Voltage and Current | Resistance

How do I choose a relay to use with one of your projects?

Choosing a relay is explained on the Relays page.

I want to use a large number of LEDs, do I need a resistor for each one?

No, you can usually connect a few LEDs of the same type in series and just use one resistor. The number of LEDs you can connect in series depends on the circuit's supply voltage. This arrangement has the advantage of reducing the total current required by the circuit. Please see the LEDs page for more details:
Further information: Connecting LEDs in series

Magnum Technologies. Visit : www.magnumprojects.com